Hubbell Lawn Mower UH32 User Manual

INSTALLATION and MAINTENANCE INSTRUCTIONS  
UH32 UNIVERSAL HOSE REEL-DIRECT DRIVE  
NOTE: These instructions are written for machine pull reels.  
If installing or servicing hand pull reel, use only those steps marked with hand  
.
All units are provided with right hand rotation unless otherwise  
specified. This means that hose is pulled off spool top left or  
bottom right (spool rotates clockwise to wind hose) when  
viewing spring end of reel. See diagram on parts page.  
WARNING  
Some reels with large or multiple springs are equipped with  
a ratcheted adjustment wrench. Follow separate instruc-  
tions for its use. Failure to use ratcheted wrench, on reels  
so equipped, could result in serious personal injury.  
Clock-type springs provide power for automatic hose take-up.  
Spring must be pretensioned at time of installation to  
insure that tension is applied to hose at all times. A tension  
adjustment spanner wrench is provided with each reel.  
INSTALLATION  
MAINTENANCE  
“IN” with 2/3  
cable off reel–  
SPRING OK  
BROKEN SPRING  
INDICATORS  
Periodically: A. Inspect hose  
for wear and check mounting  
bolts and other hardware for  
tightness.  
B. Check for broken springs  
by pulling about 2/3 hose off  
reel and observing “Broken  
Spring Indicators” on sides of  
spring canisters (Fig. 3).  
WARNING  
If machine pull reel, move machinery to position closest  
to reel before adjusting spring tension.  
“OUT” with 2/3  
cable off reel–  
SPRING  
Adjusting tension with hose extended may result in  
damage to reel or personal injury.  
BROKEN  
Figure 3  
1. Install hose if reel was purchased without hose. See  
instructions on page 4.  
NOTE: Bearings and springs are prelubricated and require no  
periodic maintenance.  
2. Insure that machinery to be serviced by reel is at  
position closest to reel.  
3. Securely mount reel in desired position using 1/2"(M12).  
WARNING  
Be sure spool is aligned with hose run.  
Do not attempt to remove spring from its housing. Clock-  
type springs can be dangerous to handle. Removal of  
spring from housing could result in personal injury.  
4. Position hose guide if supplied so hose pays-out as  
straight as possible through hose guide.  
5. Connect free end of hose to connections on machine or  
adjust hose stop so that desired length of hose extends from reel.  
SPRING REPLACEMENT  
The unique SAFETYCHANGE® spring motor consists of a  
spring and hub sealed within a housing. A replacement spring  
is supplied sealed in its housing and the old unit should be  
discarded completely.  
6. Connect flexible supply lines to swivel fitting. See HOSE  
INSTALLATION REFERENCE DRAWING.  
NOTE: Do not hard plumb to swivel fitting.  
7. Remove cover plate on spring housing to expose  
1. Turn off supply pressure to reel.  
shaft and spring hub. (See Figure 1).  
2. Insure that machinery to be serviced by reel is at  
position closest to reel. Disconnect hose from  
machine connections.  
8. Insert spanner wrench into holes in spring hub (Fig 2).  
Rotate spanner wrench counter-clockwise. Number of  
360˚ turns should match last digit in model number on  
serial plate.  
3. Wind all hose onto reel to relieve all spring tension.  
COUNTER-  
CLOCKWISE  
FOR STANDARD  
ROTATION  
SPRING  
HOUSING  
4. Remove inspection cover from face of spring housing.  
5. Rotate spool clockwise and observe inner shaft.  
COVER  
PLATE  
Shaft should rotate clockwise and hub (with  
spring attached) should remain stationary.  
NOTE: Do not attempt to remove spring if resistance is  
met or hub tends to rotate with shaft. Continue to rotate  
spool and strike end of shaft several sharp blows with a lead  
hammer or rubber mallet until shaft rotates freely  
and hub remains stationary.  
SPRING  
HUB  
SPANNER  
WRENCH  
Figure 2  
Figure 1  
6. Remove (4) bolts which secure spring motor to frame.  
CAUTION  
Do not exceed number of turns indicated on serial plate.  
Over-tensioning can cause a broken spring, sheared  
shaft or other damage.  
7. Slide spring motor off shaft and discard.  
8. Install replacement spring motor, pawls and pawl springs.  
NOTE: Pawl springs must be located between the pawls  
and the deepest section of the shaft grooves.  
Make sure that pawls and pawl springs are inserted flush  
with ends of shaft and hub or they may rub against  
inspection cover. See Fig 4, page 4.  
WARNING  
Do not attempt to relieve spring tension using spanner  
wrench. Doing so may result in personal injury.  
CONTINUED ON BACK PAGE  
 
Always specify  
SERIAL NUMBER & MODEL NUMBER  
when ordering parts.  
TO DETERMINE ROTATION OF REEL  
30  
26  
27  
25  
32  
STANDARD REVERSE  
ROTATION ROTATION  
24  
23  
Hose is played out and retracted as shown  
when viewing reel from spring motor side.  
29  
21  
22  
6
28  
27  
7
26  
25  
7
8
9
24  
13  
20  
19  
17  
29  
13  
28  
11  
27  
19  
10  
31  
13  
14*  
17  
12  
20  
16  
15  
12  
15  
1
16  
2
2
3
14  
5
4
DOG & RATCHET  
Standard Rotation....P/N 042230  
Reverse Rotation....P/N 042231  
14*  
14  
SPOOL LOCK  
All models....P/N 042227  
17  
0.75" – 1.5" ID  
HOSE ONLY  
14a  
14  
ROLLER HOSE  
GUIDES  
*Reducers included in  
Hose Adapter Kits  
when required.  
18  
340O PIVOT BASE  
HOSE STOPS  
HORIZONTAL (shown)  
TYPE  
A
SPOOL  
WIDTH  
PART  
3.00” O.D.  
NUMBER  
6"  
8"  
10"  
12"  
14"  
042210  
042211  
042212  
042213  
042214  
TYPE  
B
3.50” O.D.  
PART  
NUMBER  
FITS O.D.s  
MIN – MAX  
TYPE  
VERTICAL  
037529  
037531  
037532  
037533  
037535  
037536  
037537  
041845  
041846  
B
A
A
A
B
B
B
B
B
0.44 – 0.62  
0.62 – 0.75  
0.75 – 1.05  
1.06 – 1.30  
0.75 – 1.05  
1.06 – 1.38  
1.39 – 1.55  
1.56 – 1.87  
1.88 – 2.06  
SPOOL  
WIDTH  
PART  
NUMBER  
SPOOL  
WIDTH  
PART  
NUMBER  
6"  
8"  
10"  
12"  
14"  
042275  
042276  
042277  
042278  
042279  
4"–6"  
8"–10"  
12"–14"  
042284  
042285  
042286  
 
PAWL  
4. Unwrap hose without allowing spool to turn.  
5. Disconnect hose from elbows inside spool wrapper.  
6. Install new hose following directions below.  
SPRING HUB  
(Spring not  
shown)  
SPOOL  
SHAFT  
SPRING  
Install  
against flat  
SHAFT  
GROOVE  
END VIEW  
SIDE VIEW  
Figure 4  
HOSE INSTALLATION  
Use the following procedure to replace hose or if reel was  
ordered without hose. Refer to HOSE INSTALLATION  
REFERENCE DRAWING, below.  
9. Tighten bolts securing spring housing to reel frame.  
10. Connect free end of hose to connections on machine  
or adjust hose stop so that desired length of hose  
extends from reel.  
1. Unspool new hose from shipping spool and lay out to  
eliminate twist.  
11. Tension spring with spanner wrench. Refer to  
NOTE: This step is not essential, but will aid in winding  
operation of the reel and prolong hose life.  
INSTALLATION section.  
12. Replace inspection cover.  
2. Insert hose end through guide and connect to elbows  
inside spool wrapper. (See drawing below.)  
HOSE REMOVAL  
5. Wind the hose onto the reel spool by hand rotating  
spool in direction it turns free of spring tension.  
Use the following procedure to remove worn or damaged hose  
from reel prior to installation of new hose.  
(Normally clockwise when viewed from spring side)  
6. Adjust hose stop (not used on machine pull reel).  
7. Complete working end connections.  
1. Move machine serviced by reel to a position closest to  
reel. Spring will still be under pre-tension at this point.  
2. Turn off supply pressure to reel.  
8. Pretension reel and complete installation as  
described in REEL INSTALLATION section.  
3. Disconnect hose from machine or other attachments.  
Remove hose stop, if installed, and allow hose to  
retract onto spool. Ensure all tension is off spring by  
manually rotating spool (normally clockwise when  
viewed from spring side).  
HOSE INSTALLATION REFERENCE DRAWING  
STANDARD SPOOL  
ROTATION DIRECTION  
TO WIND HOSE WHEN  
VIEWED FROM  
OPTIONAL  
VERTICAL  
HOSE GUIDE  
LOCATION–  
REEL  
STANDARD SPOOL  
ROTATION DIRECTION  
TO WIND HOSE WHEN  
VIEWED FROM  
HORIZONTAL HOSE  
GUIDE POSITION  
(STANDARD)  
SPRING SIDE  
FITTING SIDE  
MOUNTED  
BASE UP  
SPRING  
MOTOR  
ELBOW–  
CONNECT  
SPOOLED  
HOSE HERE  
SPOOL  
DISK  
SPOOL  
DISK  
SPOOL  
WRAPPER  
SECTIONS  
HOSE ON  
SPOOL  
SWIVEL  
FITTING  
ADJUSTABLE  
HOSE STOP  
ATTACH SUPPLY LINE HERE  
NOTE: SUPPLY MUST BE  
FLEXIBLE LINE. DO NOT  
HARD PLUMB.  
OPTIONAL  
HORIZONTAL  
HOSE GUIDE  
LOCATION  
HOSE STOP  
MOUNTING  
BASE  
VIEW FROM FITTING SIDE  
VIEW FROM SPRING SIDE  
GLEASON REEL CORP.  
®
P.O. Box 26 • 600 South Clark St.  
Mayville, WI 53050–0026  
®
Phone 920–387–4120 • Fax 920–387–4189  
HUBBELL A Hubbell Company  
Printed in USA  
Bulletin No. 042872.b  
 

Graco Baby Accessories PD178040A User Manual
Grizzly Chainsaw Sharpener T23108 User Manual
Grundig MP3 Docking Station CDS2500IPW User Manual
Harbor Freight Tools Landscape Lighting 95681 User Manual
Harbor Freight Tools Saw 93211 User Manual
Hearth and Home Technologies Electric Heater SL 550TRSI AUE User Manual
Hotpoint Washer VVSR1070 User Manual
HP Hewlett Packard Microscope Magnifier HP 54520C User Manual
Hubbell Switch Series 2015 User Manual
IBM Computer Drive 28L2234 User Manual