iLive DVD Player ID200B User Manual

USER’S GUIDE  
V:1319-0324-10  
ID200B  
DVD Player with Dock for iPod  
For the most up-to-date version of this Users Guide, go to www.ilive.net  
 
fcc Warnings  
NOTE: This equipment has been tested and found to comply with  
the limits for a Class B digital device, pursuant to Part 15 of the FCC  
Rules. These limits are designed to provide reasonable protection  
against harmful interference in a residential installation. This equip-  
ment generates, uses, and can radiate radio frequency energy and, if  
not installed and used in accordance with the instructions, may cause  
harmful interference to radio communications. However, there is no  
guarantee that interference will not occur in a particular installation.  
If this equipment does cause harmful interference to radio or televi-  
sion reception, which can be determined by turning the equipment  
off and on, the user is encouraged to try to correct the interference  
by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from  
that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for  
help.  
additional Warnings  
The apparatus shall not be exposed to dripping or splashing and  
that no objects filled with liquids, such as vases, shall be placed  
on apparatus.  
L’appareil ne doit pas être exposé aux écoulements ou aux écla-  
boussures et aucun objet ne contenant de liquide, tel qu’un vase,  
ne doit être placé sur l’objet.  
Main plug is used as disconnect device and it should remain  
readily operable during intended use. In order to disconnect the  
apparatus from the mains completely, the mains plug should be  
disconnected form the mains socket outlet completely.  
La prise du secteur ne doit pas être obstruée ou doit être facile-  
ment accessible pendant son utilisation. Pour être complètement  
déconnecté de l’alimentation d’entrée, la prise doit être débran-  
chée du secteur.  
Battery shall not be exposed to excessive heat such as sunshine,  
fire or the like.  
Les piles ne doivent pas être exposées à de forte chaleur, tel qu’à  
la lumière du soleil, au feu ou autres choses de semblable.  
Caution marking is located at the rear of the apparatus.  
Les marquages sont inscrits de derrière de l’appareil.  
The marking information is located at the rear of apparatus.  
Les précautions d’emploi sont inscrites de derrière de l’appareil.  
CUstOmeR HeLPLINe | 1-314-621-2881  
iLive | ID200B  
3
 
dVd Player With dock for iPod  
features  
included  
• Made for iPod  
• Remote control: requires 2 AAA  
batteries (not included)  
• DVD player: DVD, DVD±R/RW  
• CD player: CD, CD-R/RW, JPEG CD  
• Progressive scan  
• Audio/video cable  
• NTSC/PAL  
• On-screen display for iPod and DVD  
• Supports Universal docking brackets  
• Basic iPod controls from remote  
• Composite video output  
• Component video output  
• Coaxial digital audio output  
• Remote control  
• Soft eject iPod docking drawer  
• AC power: built-in AC power cable  
4
iLive | ID200B  
 
taBle of contents  
introduction  
6
8
setuP  
Basic teleVision connection  
adVanced teleVision connection  
iPod  
9
10  
11  
12  
13  
14  
16  
dVd and cd  
setuP menu  
softWare uPdates  
comPany information  
CUstOmeR HeLPLINe | 1-314-621-2881  
iLive | ID200B  
5
 
introduction  
PoWer  
disc draWer  
Press to turn the DVD  
player off and on.  
oPen/close  
OPEN/  
CLOSE  
iPod docking drawer  
Press to open and close.  
DVD  
/
CD PLAYER  
STOP  
POWER  
PLAY/PAUSE  
SOURCE  
Play/Pause  
stoP  
source  
Press to play or pause a Press to stop a CD, DVD, Press to switch between  
DVD, CD, or iPod.  
or iPod during play.  
CD/DVD and iPod  
mode.  
comPonent Video  
outPut  
comPosite Video  
outPut  
Y
Pb/Cb  
Pr/Cr  
120V  
~
60Hz  
VIDEO  
L
R
COAXIAL  
DIGITAL  
AUDIO OUT  
VIDEO OUT  
stereo audio  
outPut  
coaXial digital  
audio outPut  
ac PoWer  
6
iLive | ID200B  
 
PoWer  
Press to power the DVD  
player off or on.  
oPen/close  
Press to open or close the  
DISC DRAWER.  
OPEN/  
CLOSE  
mute  
Press to mute the volume.  
MUTE  
SUBTITLE  
ANGLE  
PROG  
suBtitle  
Press to cycle through the  
available subtitle options.  
1
4
2
5
3
6
numBer keyPad  
angle  
Press to activate the angle  
feature on supported DVDs.  
goto  
Press the GOTO button to  
search for a specific title  
chapter or time.  
7
8
9
Prog  
Press to program a loaded  
disc to play tracks or chap-  
ters in a specified order.  
GOTO  
disPlay  
Press to view the on-screen  
display.  
10/0  
10+  
SHUFFLE  
AUDIO  
DISPLAY  
audio  
Press to cycle through the  
available audio options.  
shuffle  
Press to play iPod in a  
random order.  
SETUP  
ZOOM  
setuP  
Press to access the setup  
menu.  
Zoom  
Press repeatedly to zoom in  
and out on the loaded DVD.  
ENTER  
title  
Press to access the loaded  
DVD’s title menu.  
directional/enter  
TITLE  
MENU  
menu  
Press to access the loaded  
DVD’s menu.  
n/P  
Press to switch between  
NTSC and PAL.  
N/P  
SOURCE  
source  
Press to switch between  
CD/DVD and iPod mode.  
f.BWd/f.fWd  
Press and hold to fast  
forward or rewind a loaded  
disc.  
PreV/neXt  
Press to skip between  
chapters or tracks.  
rePeat  
Press to repeat a single  
chapter or track, or and  
entire disc.  
Play/Pause  
Press to play or pause a CD,  
DVD, or iPod.  
REPEAT  
STEP  
A-B  
L/R  
SLOW CLEAR  
VOL  
steP  
With a DVD paused, press  
repeatedly to step through  
the DVD one frame at a  
time.  
stoP  
Press to stop a CD, DVD, or  
iPod during play.  
l/r  
Press to switch the audio  
channel.  
a-B  
Press to repeat a specified  
section of a loaded DVD.  
Volume  
Press to adjust the volume.  
sloW  
Press to play the loaded  
DVD in slow motion.  
clear  
Press to delete numbers  
typed in using the number  
keypad.  
CUstOmeR HeLPLINe | 1-314-621-2881  
iLive | ID200B  
7
 
setuP  
Power  
Plug the attached AC cord into a  
standard AC power outlet to power the  
home theater system.  
remote  
Requires 2 AAA batteries (not included)  
8
iLive | ID200B  
 
Basic teleVision connection  
composite Video output  
Y
Pb/Cb  
Pr/Cr  
120V  
~
60Hz  
VIDEO  
L
R
COAXIAL  
DIGITAL  
1 Plug the included RCA audio/video  
cable into the comPosite Video  
outPut (yellow) on the DVD player  
and the composite video input  
(yellow) on a television.  
AUDIO OUT  
VIDEO OUT  
AUDIO INPUT  
VIDEO INPUT  
2 Plug the remaining plugs on the  
included RCA audio/video cable into  
the rca stereo audio outPuts  
(red and white) on the DVD player  
and the RCA stereo audio inputs (red  
and white) on a television.  
TELEVISION  
3 Adjust the television’s input setting  
to correspond to the inputs used  
when connecting the DVD player.  
CUstOmeR HeLPLINe | 1-314-621-2881  
iLive | ID200B  
9
 
adVanced teleVision connection  
component Video output  
TELEVISION  
Requires a component video cable (not  
included).  
COMPONENT VIDEO INPUTS  
1 Plug a component video cable into  
the comPonent Video outPuts  
(green, blue, red) on the DVD player  
and the component video input  
(green, blue, red) on a television.  
Y
Pb/Cb  
Pr/Cr  
120V  
~
60Hz  
VIDEO  
L
R
COAXIAL  
DIGITAL  
AUDIO OUT  
VIDEO OUT  
2 Plug the included RCA audio/video  
cable into the rca stereo audio  
outPuts (red and white) on the  
DVD player and the RCA stereo  
audio inputs (red and white) on a  
television.  
Y
Pb/Cb  
Pr/Cr  
120V  
~
60Hz  
VIDEO  
L
R
COAXIAL  
DIGITAL  
AUDIO OUT  
VIDEO OUT  
AUDIO INPUT  
3 Adjust the television’s input setting  
to correspond to the inputs used  
when connecting the DVD player.  
TELEVISION  
digital audio output  
Y
Pb/Cb  
Pr/Cr  
120V  
~
60Hz  
VIDEO  
L
R
COAXIAL  
DIGITAL  
Requires a coaxial digital audio cable  
(not included).  
AUDIO OUT  
VIDEO OUT  
1 Plug a coaxial digital audio cable  
into the coaXial digital audio  
outPut (black) on the DVD player  
and the coaxial digital audio input  
(black) on a television or stereo  
system.  
COAXIAL DIGITAL  
INPUT  
STEREO SYSTEM  
OR  
TELEVISION  
2 Adjust the television or stereo  
system’s input setting to correspond  
to the input used when connecting  
the DVD player.  
10 iLive | ID200B  
 
iPod  
tV interface  
docking an iPod  
1 When connected to a television, the  
docked iPod can be controlled from  
the on-screen display.  
1 Press the face of the iPod docking  
draWer.  
2 Connect the iPod to the connector  
2 Use the directional/enter  
buttons to navigate and make  
selections on the on-screen display.  
inside the iPod docking draWer.  
When the speaker is plugged in, using  
AC power, the docked iPod will charge.  
Playing an iPod  
1 Follow the instructions for docking  
an iPod.  
2 Press the PoWer button to turn the  
DVD player on.  
3 Press the source button to switch  
to iPod mode.  
After switching to iPod mode,  
“INITIALIZING” will appear on the TV  
display if connected. Wait until the  
display reads “CONNECT OK” before  
moving on to step 4.  
4 Use the directional/enter  
buttons to navigate and make  
selections on the on-screen display.  
11  
 
dVd and cd  
Playing a dVd or cd  
Playing a JPeg Photo cd  
1 Connect the DVD player to a  
television and press the PoWer  
button to turn the DVD player on.  
1 Press the source button to switch  
to DVD mode.  
2 Press the oPen/close button to  
open the disc draWer.  
3 Load a JPEG Photo CD into the disc  
draWer, label side facing up, and  
press the oPen/close button to  
close the disc draWer.  
4 Press the directional/enter  
buttons to highlight and select  
photos from the loaded JPEG CD.  
2 Press the oPen/close button to  
open the disc draWer.  
3 Load a DVD or CD into the disc  
draWer, label side facing up, and  
press the oPen/close button to  
close the disc draWer.  
4 The loaded DVD or CD will begin  
playing automatically. If it does not,  
press the Play/Pause button.  
Programming a dVd or cd  
1 Follow the instructions for “Playing a  
DVD or CD.  
2 Press the Prog button on the  
remote.  
3 Press the directional/enter  
buttons to select a program memory  
slot.  
4 Add titles and chapters or tracks  
to the program menu using the  
numBer keyPad.  
Titles and chapters or tracks will play  
in the order they are added.  
5 Press the Play/Pause button to  
play the programmed DVD or CD.  
6 To cancel the program, press the  
oPen/close button to open the  
disc drawer.  
12 iLive | ID200B  
 
setuP menu  
accessing the dVd setup menu  
To access the DVD setup menu, press  
the setuP button on the remote.  
dVd setup menu  
TV SYSTEM  
SCREEN SAVER  
VIDEO  
TV TYPE  
DEFAULT  
OSD LANGUAGE  
AUDIO LANGUAGE  
SUBTITLE LANGUAGE  
MENU LANGUAGE  
AUDIO OUTPUT  
DOWNMIX  
BRIGHTNESS  
CONTRAST  
HUE  
SATURATION  
SHARPNESS  
CUstOmeR HeLPLINe | 1-314-621-2881  
iLive | ID200B 13  
 
softWare uPdates  
overview  
Just as Apple continues to update and improve it’s software and hardware, iLive  
works to remain up-to-date with the latest offerings from Apple.  
ID200B.  
checking your dVd players current software  
1. Power on DVD player.  
2. Remove any CD or DVDs from the disc draWer.  
3. Press “9735using the numBer keyPad on the remote.  
4. Your DVD player’s current software version will be listed after “Software data-  
code. Write down this number for reference.  
the list of products.  
6. Select DOWNLOADS, then compare your DVD player’s software datacode to  
the code listed in the Firmware Update section. If your DVD player’s datacode  
does not match the most recent firmware update, then your player can be  
updated.  
7. Press the oPen/close button on the DVD player to exit the software menu.  
WARNING: Do not adjust the region code on the DVD player. Changing the region  
code can result in issues with your DVD player’s ability to read DVDs.  
14 iLive | ID200B  
 
Preparation  
You will need all of the following.  
Computer connected to the Internet.  
CD drive that is capable of reading and writing CD disk  
Blank CD-R or CD-RW disc.  
creating a firmware disk  
the list of products.  
2. Select DOWNLOADS, then click on the most recent firmware update and save  
file to your computer.  
3. Load a blank CD into a CD writable drive.  
4. Copy and Paste or Drag and Drop firmware file to CD drive, and write (burn)  
file to CD.  
installing updates  
1. Power on DVD player.  
2. Press the oPen/close button to open the disc draWer. Insert the firm-  
ware disc. Press the oPen/close button to close the disc draWer.  
The DVD player will read disk and automatically begin update process. The up-  
date process will take several minutes.  
3. The DVD player will automatically power off when the update is complete.  
4. Once update is complete, power on the DVD player and remove update disk.  
5. Press the setuP button to access the system setup menu.  
6. Select “Default Reset” and press the enter button.  
7. Your DVD player is now updated.  
The following events may cause the writing of the firmware update to the player to be halted and the  
player to no longer operate properly.  
DO NOT unplug the power cord during the firmware update process.  
Avoid loss or interruption of power during the firmware update process.  
DO NOT press the power button on the unit during the firmware update process.  
Check the firmware update disc for dirt or scratches before beginning the firmware update process.  
CUstOmeR HeLPLINe | 1-314-621-2881  
iLive | ID200B 15  
 
comPany information  
green initiative  
environmental Commitment to ‘Protect for  
today and sustain for tomorrow’  
2009 marks the official launch of DPI, Inc.’s  
corporate campaign for a greener and cleaner  
world. DPI and its four brands, iLive, WeatherX,  
Capri, and GPX, are building upon environmental  
initiatives introduced at all of their facilities to help  
formulate and sustain significant and important  
conservation efforts within its manufacturing and  
marketing communities. In addition to targeting  
and selecting energy efficient product features, and  
structuring ‘green office’ procedures, other initial  
program efforts include:  
Reduction of all packaging sizes  
Recyclable plastics for clamshell packages,  
with a plan to eventually replace plastic with  
recyclable paper  
Recycled fiber board in place of the polyfoam in  
packing boxes  
Recycled plastics in place of the virgin material  
in product construction  
international support  
To download this User’s Guide in English,  
Spanish, or French, visit the support section at  
Para transferir esta guía de usuario en inglés,  
español, o francés, visite la sección de la ayuda en  
Pour télécharger ce guide de l’utilisateur en  
anglais, espagnol, ou français, visitez la section de  
contact information  
Address: 2116 Carr Street, St. Louis MO, 63106  
Phone: 1-314-621-2881  
Fax: 1-314-588-1805  
Parts Email: [email protected]  
© 2009 Digital Products International (DPI, Inc.) | All other trademarks appearing herein are the property of their respective owners. Specifications are  
subject to change without notice  
 

Graco Baby Playpen ISPP045AB User Manual
Grizzly Drill T10538 User Manual
Harman Boiler SF160 User Manual
Honeywell Humidifier HDC 200PDQ User Manual
Hotpoint Refrigerator HSS22IFM User Manual
HP Hewlett Packard Personal Computer dx5150 User Manual
Husqvarna Tiller crt51 User Manual
Husqvarna Tiller CT20 User Manual
IBM Computer Hardware 2292 User Manual
Icom Marine Radio IM422 User Manual